Remington 1100 magnum.. issues

F

fadetoblack188

Member
Ok so I have a Remington 1100 magnum with a 30 inch fixed mod barrel.

This gun being that it is the magnum receiver doesn’t want to cycle 2 3/4 loads. Some guys on the internet have no issues cycling them. Some guys have the same issue I am.

I have read that you can open the gas port a tiny bit with a drill bit but then will 3 inch loads be to much?

This gun was passed down by my godfather who died so I want to be using it so bad. But I have no reason other then skeet or pheasant . I don’t want to bring it near the salt water hear for ducks and destroy it.

What’s everyone’s thoughts ? I have tried heavy pheasant loads
 
I think your best solution is to buy a standard 1100 12 ga. barrel for 2 3/4" shells. The receivers are the same on the Magnum and non-Mag so a standard 12 ga. barrel will work and allow you to shoot lighter loads. There are a lot of used 1100 barrels on eBay. Some with vent rib and some without. Just make sure you don't buy one that is for an 1187. By getting a different barrel you can find a 26" or 28" in IC or Mod. which would be a better choice for sheet or pheasants.
 
Weimdogman said:
Changing the barrel should make no difference. See a real gunsmith.
Click to expand...
What do you mean "no difference"? It certainly will changing to a standard 2 3/4" barrel. You will be able to shoot non-magnum shells. The standard barrel has two gas ports, the 3" magnum barrel only has one.
 
Here's a nice 26" vent rib barrel choked Skeet. That choke would be fine for pheasants also.

www.ebay.com

Remington 1100 Skeet Barrel 12 ga. 25.5â | eBay

<p>This is a pre-owned Remington 1100 12 gauge shotgun barrel in very good condition. There is a small imperfection below the front sight (see images). </p><p>The bore is rust free, bluing is 98%. </p><br /><p>The total barrel length is 29 1/8â, muzzle to chamber area measures 25 11/16â in...
www.ebay.com

Or here's another 26" choked IC

www.ebay.com

Remington 1100 12 Ga 26” Vent Rib Fixed IC Choke 2 3/4” Shell Barrel Read #2190 | eBay

<p>Remington 1100 12 Ga 26” Vent Rib Fixed IC Choke 2 3/4” Shell Barrel. Condition is Used. I have a Remington 1100 vent rib improved cylinder choke barrel for sale. This barrel is used and several marks towards the muzzle. I’m not sure what the marks are from, they are similar to pitting, but...
www.ebay.com
 
fadetoblack188 said:
I live in a liberal state. Won’t ship
Click to expand...
Where do you live? It shouldn't matter to just ship a barrel but you should still be able to have it shipped to FFL in your area.
 
fadetoblack188 said:
Ok so I have a Remington 1100 magnum with a 30 inch fixed mod barrel.

This gun being that it is the magnum receiver doesn’t want to cycle 2 3/4 loads. Some guys on the internet have no issues cycling them. Some guys have the same issue I am.

I have read that you can open the gas port a tiny bit with a drill bit but then will 3 inch loads be to much?

This gun was passed down by my godfather who died so I want to be using it so bad. But I have no reason other then skeet or pheasant . I don’t want to bring it near the salt water hear for ducks and destroy it.

What’s everyone’s thoughts ? I have tried heavy pheasant loads
Click to expand...
How does your mag tube look? Rusting/pitting on the mag tube causing the gas check to not seal properly is the main reason for poor cycling on these. Have had that issue myself. Not much you can do about it, if this is the case.

You could try a new gas check/seal but the new style are pretty bad compared to the old UFO style. And its almost impossible to find good condition old stock anymore.

Id personally just shoot mag 2.75 loads out of it and enjoy using the gun. 1 3/8 1300 or so loads will cycle just fine i bet. Yeah you cant use that at the trap range, but theres not many 1100 mag that cycle trap loads well to begin with.
 
KEOutdoors said:
How does your mag tube look? Rusting/pitting on the mag tube causing the gas check to not seal properly is the main reason for poor cycling on these. Have had that issue myself. Not much you can do about it, if this is the case.

You could try a new gas check/seal but the new style are pretty bad compared to the old UFO style. And its almost impossible to find good condition old stock anymore.

Id personally just shoot mag 2.75 loads out of it and enjoy using the gun. 1 3/8 1300 or so loads will cycle just fine i bet. Yeah you cant use that at the trap range, but theres not many 1100 mag that cycle trap loads well to begin with.
Click to expand...
I replaced a while back with the newer one. I read somewhere to try two o rings. I don’t no we will see
 

Attachments

  • IMG_5231.jpeg
    IMG_5231.jpeg
    1.3 MB · Views: 5
KEOutdoors said:
How does your mag tube look? Rusting/pitting on the mag tube causing the gas check to not seal properly is the main reason for poor cycling on these. Have had that issue myself. Not much you can do about it, if this is the case.

You could try a new gas check/seal but the new style are pretty bad compared to the old UFO style. And its almost impossible to find good condition old stock anymore.

Id personally just shoot mag 2.75 loads out of it and enjoy using the gun. 1 3/8 1300 or so loads will cycle just fine i bet. Yeah you cant use that at the trap range, but theres not many 1100 mag that cycle trap loads well to begin with.
Click to expand...
I will give the 1 3/8 a shot see if they cycle. Thank you
 
I have several 1100’s and the only time I have cycling problems is from plastic buildup in the chamber. Scrubbing the chamber really good with a brass brush has always worked well for me.
 
You must log in or register to reply here.
Back
Top